D.A.S. M-14:2 Specifications

M-14:2 Professional Stereo MixerPROFESSIONAL STEREO MIXERM-14:2ELECTRONICSELECTRONICSB370031OC03

8M-14:2PROFESSIONAL STEREO MIXER2. STEREO INPUT SECTION1. STEREO INPUT JACKSThese are unbalanced 1/4" phone jacks which input a stereosource with

9M-14:2PROFESSIONAL STEREO MIXER6. AUX 2 CONTROLSThis knobs control the level of the signals sent to AUX 2 bus. The channel signals mixed by this bus

10M-14:2PROFESSIONAL STEREO MIXER3. MASTER SECTION1. MAIN MIX OUTPUTS These are balanced XLR type output jacks with anominal output/impedance of +4dB/

11M-14:2PROFESSIONAL STEREO MIXER8. HEADPHONES OUTPUT JACK (1/4" TRS STEREO JACK)These jacks (tip=left, ring=right, sleeve=GND) may be con-nected

12M-14:2PROFESSIONAL STEREO MIXER14. PHONE GAIN CONTROLThis control sets the level at the headphone jack. 15. TO MIX SWITCH When this switch is on the

13M-14:2PROFESSIONAL STEREO MIXERRear PanelRear Panel1. INPUT/OUTPUT CONNECTORS A1. CHANNEL INSERT I/O JACKThese are input/output jacks located betwee

14M-14:2PROFESSIONAL STEREO MIXER2. INPUT/OUTPUT CONNECTORS B1. POWER SWITCHThis switch turns the power ON/OFF. When in the ON position, the power ind

15M-14:2PROFESSIONAL STEREO MIXERPoints to RememberPoints to Remember- In all cases, use good quality twin screened audio cable. Check for instability

16M-14:2PROFESSIONAL STEREO MIXERConnectionsConnectionsD.A.S ELECTRONICS products are wired to reflect accepted wiring practices used throughout the w

17M-14:2PROFESSIONAL STEREO MIXERGrounding on the RoadGrounding on the RoadMany of the above procedures are difficult to use on the road. For example,

ContentsContentsWelcomeWarning...

18M-14:2PROFESSIONAL STEREO MIXERCONNECTOR AND CABLE CONFIGURATIONSConnector and cable configurations recommended for use with the M-14:2.These cables

19M-14:2PROFESSIONAL STEREO MIXERApplicationsApplicationsPROFESSIONAL STEREO MIXER M-14:2ELECTRONICS

20M-14:2PROFESSIONAL STEREO MIXERBlock DiagramBlock Diagram

21M-14:2PROFESSIONAL STEREO MIXERSpecificationsSpecifications...*0dB=0.775Vrms, 0dBV=1Vrms- GENERALMaxim

22M-14:2PROFESSIONAL STEREO MIXERSpecifications ...0dB=0.775Vrms, 0dBV=1Vrms- INPUT- OUTPUT * Specification

23M-14:2PROFESSIONAL STEREO MIXERServiceServiceProceduresTake steps to insure the problem is not related to operator error or other products within th

NOTE

MADE IN CHINADecember 2003 9007982200 AInter-M, Ltd. (Korea) began operations in 1983.Since then, Inter-M has grown to become one of the largest ma

1M-14:2PROFESSIONAL STEREO MIXERWelcomeWelcomeAll of the co-workers here at D.A.S ELECTRONICS are dedicated to providing excellent products with inher

2M-14:2PROFESSIONAL STEREO MIXERUnpackingAlthough it is neither complicated to install nor difficult to operate your set, a few minutes of your time i

3M-14:2PROFESSIONAL STEREO MIXERInstallationInstallationEnvironmentNever place this product in an environment which could alter its performance or red

4M-14:2PROFESSIONAL STEREO MIXERFeaturesFeatures- 6MONO, 10MONO INPUT AND 4 STEREO INPUTAny sound source of microphones, cassette decks, electronic gu

5M-14:2PROFESSIONAL STEREO MIXERFront PanelFront Panel 1. MONO INPUT SECTION1. MIC INPUTA 3-pin XLR-type connector is used for balanced lowimpedance

6M-14:2PROFESSIONAL STEREO MIXER2. BALANCED LINE INPUT CONNECTORSA standard 1/4" phone jack is used for balanced or unbalanced line level signal

7M-14:2PROFESSIONAL STEREO MIXERઆModificationsMono channel Aux send 2 are post-fader. This modification changes Aux send2 to be pre-fader instead ofp